Design and interior blog

Place everything you need in one-room flat - not an easy case: furniture stores, took a lot of places.
But if the interior to make itself - transformed by the same collection in a single volume, takes up little space, a small room and turn into a comfortable home.
With a universal design-wall, in which there is a minimal set of all the necessary capacities, we introduce in today’s issue of KDM.

For furniture, designed for small apartments, or single units, subject to special requirements: in addition to maximum capacity and minimum size (in fact in a small room, each square centimeter of the account) it should be possible and multifunctional. Of course, this can be achieved and made up a set of individual cases, tumbochek, shelving, mezzanine and other items purchased in the store. But then would have to pre-spend much time searching for appropriate-sized elements. In addition, they will differ in style and decoration.
To solve the problem, if you get the most for the manufacture of furniture. In this case, it all depends on the skills, capabilities and imagination of the home master.
Today, we introduce readers to the wall of a universal design for living room.

I propose a simple construction of the wall, which combines the clothes and the bookcase, bed, storage btslya, clothing, footwear, glassware, books, etc. In addition, the facade panel folding bed is a folding desk, a wardrobe door - a mirror. In other words, a wall, replace the whole set.
Due to its compactness, it is located along the entire length of the wall without taking up much space. Dimensions Construction 2496X1950 X X400 mm. In a large room can serve as a partition wall dividing the space into different functional zones. In this case it is necessary to decorate the facade and the second wall, plastered like wallpaper or self-cleaning film (it should match the finish in accordance with the general decision of the interior.
To produce the bulk of the wall is better to use the furniture panels, as they do not require further finishing, but if not, fine and normal chipboard 16 mm thick. In their design, you can use veneer, plastic, self-adhesive tape, fabric or artificial leather. In the proposed version of the plane plastered exterior veneer, and all internal - cleaning wallpaper.
First, collect the basic skeleton. Mount it easier in a horizontal position, face down - is easier to connect horizontal elements with vertical; after installation, you can not turning the whole construction, secure the rear wall.
Further assembly can be produced in a vertical position, as well as basic (carrying) the frame is ready. The upper branch, designed to store books, dishes, small objects are equipped with a set of shelves and partitions, secured to the bearing elements on the screw. A number of volumes equip pair of sliding doors or (for sending) glasses. Inside the wardrobe, in its upper part, maintains the bar for the shoulder and hooks for clothes. To the right side of the door attaches to the mirror - it may be located both on the outside, and on the inside. All opening doors hang on the walls of Piano Hinges.

Basement construction of drawers fitted with two types: the four - in a row with the sizes of 475X180 mm front panel, and two - one above the other with the size - 500X296 mm. Each panel is gathered from the CPD and the three boards with thickness of 10-15 mm. In the bottom match orgalit or plywood.
The most difficult part - drop the bed. Its peculiarity is that when it is in the retracted position of the bottom panel recline desk, but retracted - supporting legs. Since the bottom bed is also a front line of furniture and has the notches, it can not bear the burden of the weight of underlying rights. Therefore, the basis for the spring mattress is the lattice of the bars section of 40 X 20 mm. By nontsami each slat is connected to tsargami on wooden inserts shipah. By tsargam on both sides of the back are attached, one must be somewhat higher. This is done to create a cushion stops.
yrezannye tabletop and support legs are mounted to the front panel for Piano Hinges. Then screw on the bottom of the bed is fixed to the assembled base. Home screws should be zaglublyat that they do not prevent the subsequent finishing. Table equip telescopic or other brackets, which serve as limiters opening. At the top of the table
provided mortise locks, the reeds are made in the hand, not giving a table Sit at decomposition status of the bed. Supporting legs also have limitations, but more than a simple design - you can, say, use the piece of leather belts.
The finished bed is mounted on a Piano Hinges to the front of the bed full of branches, with an indent from the edge of 16 mm. Latch in the raised position serves two mortise lock.
Upon completion of erection of the principal amount of start decorating. All exterior panels okleyte veneer using a joiner, kazeinovy glue or PVA. Glue veneer to be from the bottom up to avoid air bubbles formed. The interior surfaces of walls, as well as drawers okleyte cleaning with paper or synthetic paper.
After that all the product several times lakiruetsya. Better use of parquet lacquer, as it provides a solid surface, but can and NC-216. Additional adornment a old tape. Cut from the strip fix «Feniisom» (or any other nitrokleem) on scheduled lines. Then the whole construction again varnish.

konec posta pered codom ADS ### konec posta posle coda ADS